Talk to an expert
M-F 7am to 5pm PST
800-562-6006
info@ccisolutions.com

Doug Fleenor Design

Showing 1 - 4 of 4 Products

DFD TERM-5

DFD TERM-5 110-Ohm Terminator (3-Pin & 5-Pin)

5-pin DMX terminator with LED

The DFD TERM-5 DMX Terminator plugs into the XLR feed-through connector of the final DMX512 device on a control cable. It improves signal reliability by preventing reflections and reducing ringing. A "happy" LED indicates a strong signal. Three Tranzorb transient-absorbing diodes suppress spikes caused by electrical storms. Radio frequency interference (RFI) is bypassed to chassis by the .001uF capacitance of the Tranzorb diode.

Read more
$49.99

List Price $61.00

Save 18% with CCI Solutions

DFD PRE10-P DMX512 Preset Console

DFD PRE10-P DMX512 Preset Console with 10 Preset Lighting Looks

Takes up to 10 snapshots, fade times 0-999 seconds, works in conjunction with lighting console

The DFD Preset 10 Portable [PRE10P] is a super simple way to give someone 10 preset lighting looks to choose from in portable applications. The PRE10P is a DMX512 playback device that can take up to ten snapshots from a DMX console and play them back at the press of a button. Fade times can be set from 0 to 999 seconds. Each PRE10P can work in conjunction with a lighting console, automatically switching between preset and console control. When the console generates DMX, the PRE10P goes off-line and the console operates normally. Upon loss of DMX from the console, the PRE10P either returns to its previous preset or holds the last look (jumper selectable).

Features:

  • 10 preset lighting looks
  • Takes up to 10 snapshots, which can then be played back at the press of a button
  • Fade times: 0-999 seconds (default = 2 seconds)
  • Works in conjunction with lighting console
  • Goes off line so console operates normally when DMX is generated
  • When DMX stops, returns to previous preset or holds last look
Read more
$523.99

+ Free Shipping

List Price $632.00

Save 17% with CCI Solutions

DFD DMX512 Line Tester

DFD DMX512 Line Tester line tester

Line tester, 5-pin (male), +/-data red and green LED indicators, 1.9” x 0.8”

The DFD DMX512 Line Tester instantly displays the presence of the +Data and -Data signals when plugged into a DMX control line or feed-through connector. It serves as a perfect pocket sized tool for troubleshooting DMX512 cabling. Observing the indicators while fading all the dimmers from zero to full will detect if either line is stuck high. Swapped +Data and -Data lines can be determined by sending all dimmers to full.

Features

  • 5-pin male connector
  • Data + green T1 light emitting diode (LED) indicator
  • Data - red T1 light emitting diode (LED) indicator
  • Effective input impedance: 220 Ohms (each line)
  • Power input: none, draws power from DMX line
Read more
$55.00
DFD PRE10-A DMX512 Architectural Preset Console

DFD PRE10-A DMX512 Architectural Preset Console with 10 Preset Lighting Looks

Take up to 10 snapshots, fade times of 0-999 seconds, works in conjunction with lighting console

The DFD Preset 10 Architectural [PRE10A] is a super simple way to give someone 10 preset lighting looks to choose from in permanent install applications. The PRE10A is a DMX512 playback device that can take up to ten snapshots from a DMX console and play them back at the press of a button. Fade times can be set from 0 to 999 seconds (default is 2 seconds). As mentioned above, this unit is designed for permanent installation applications, and as such is designed to be wall-mounted in a convenient place to allow you quick access to switching between presets for your lighting system.

Features:

  • 10 preset lighting looks
  • Takes up to 10 snapshots, which can then be played back at the press of a button
  • Fade times: 0-999 seconds (default = 2 seconds)
  • Works in conjunction with lighting console
  • Goes off line so console operates normally when DMX is generated
  • When DMX stops, returns to previous preset or holds last look
Read more
$523.99

List Price $632.00

Save 17% with CCI Solutions